SysLOCATE Customer LOGIN instructions

1. From a PC, go to the web address www.syslocate.com.
2. Enter your Username and Password found in your SysLOCATE paperwork.
3. Click "LOGIN".
   Your Device List will appear showing the serial number.
4. Click "TRACK" (right side of page).
   The Mapping page will appear.
5. Click "LOCATE" once to find your vehicle (takes 10-30 seconds).
6. The last successful location shows as a BLUE balloon on the map.
7. The address and speed (if moving)shows up in the column, left of the map.
8. To change mapping view click "Map", "Satellite" or "Hybrid" located inside map upper right hand corner.

Setting "Alerts"

On mapping page click "Alerts" (located above map, right-side of page)
This screen allows you to specify the cell phone number(s) and email address(es) where the alerts for speed, geofence and unit disconnect are sent.

1. Enter Cell phone number(s) 10 digit number e.g. 6047297624.
2. Enter email address(es) in email field.
3. Click "Save".

After settings are confirmed, "On" will appear to the right of Alerts on mapping page.

Setting a "Speed" Limit Alert

You can set alerts for excessive speed. If this speed is exceeded, you will be notified.

1. Click "Speed" above map on mapping page.
2. Select a speed limit from drop down list.
3. Click "Save".

After settings are confirmed, "On" will appear to the right of "Speed" on mapping page.

Setting a "Geofence" Alert

Create a boundary where you are notified when your vehicle enters or exits.

1. Click "Geofence" above map on mapping page.
2. Follow example and enter address in long form.
3. Set Radius (0.1 – 624) miles.
4. Click "Preview".
   Your settings appear on small map to the right of your settings.
5. When previewed address and radius are correct click "Save".

After settings are confirmed, "On" will appear to the right of Geofence on mapping page.

Setting a "Disconnect" Alert

Disconnect alerts are sent when power to your unit is disconnected for more than one minute.

1. Click "Disconnect" above map on mapping page.
2. Click "Enable".

After settings are confirmed "On" will appear to the right of Disconnect on mapping page.

Voice Command from Cell Phone

1. From a PC, go to the web address WWW.SYSLOCATE.com.
2. Enter your Username and Password found in your SysLOCATE paperwork.
3. Click "LOGIN".
   Your Device List will appear showing the serial number.
4. Click "Account Info".
   Make sure your cell phone number is in the PHONE field, if not click "Edit Information" an enter your 10 digit cell phone # without dashes (-) ex. 9545551212.
5. Click "Save".
6. From your cell phone dial 888-744-0527.
   Based on your "Account Info" setup the Voice Command system will recognize you.
7. Personal Welcome Message
   1. Say "Locate" or press "1" to locate your vehicle right now.
   2. Say "Address" or press "2" to get your vehicle’s last known address.
   3. Say "Set Instafence" or press"3" to set a small geofence around your vehicle.
   4. Say "Unset" or press "4" to remove small geofence from around your vehicle.
   5. Say "New Device" or press "5" to choose another device from your account.

Voice Command from phone # not in "Account Info"

1. From any phone Dial 1-888-744-0527.
2. Welcome Message
   1. Say or enter your phone number (found on Account Info page).
   2. Say or enter your IVR PIN # (found on Account Info page).
      Once voice command recognizes your input, the personal Welcome Message starts.
3. Personal Welcome Message
1. Say "Locate" or press "1" to locate your vehicle right now.
2. Say "Address" or press "2" to get your vehicle’s last known address.
3. Say "Set Instafence" or press"3" to set a small geofence around your vehicle.
4. Say "Unset" or press "4" to remove small geofence from around your vehicle.
5. Say "New Device" or press "5" to choose another device from your account.

For technical support or questions regarding your account please call 1-877-692-6966 or email info@syslocate.com.